The QNAP TS-230 NAS storage drive is best for home media storage. Basically, a NAS is a Network-attached storage drive that usually helps to store the leather files such as photos, documents, or videos for a bit longer time. Moreover, it provides more space as compared to mobile phones or computer devices. The smart QNAP TS-230 NAS drives come with the most decent hardware and its classy design makes it more elegant. It is ideal for home use but it might look a little bit out of place in an office setting.
Besides, the QNAP TS-230 storage drive comes in a baby blue color and this kind of color doesn’t go with most traditional places. However, this small factor about its color and look will not be going to affect the pros of this NAS device. Basically, this smart NAS drive is made for home use and its high relative factors operate it at a low noise level and enable high-draw power brick.
Safety Instructions before performing the QNAP TS-230 NAS operation.
Before performing the basic operation of the QNAP TS-230 NAS storage drive, you should read all the following safety instructions. Generally, these instructions ensure the personal and environmental safety of the user. Read these safety instructions before performing any operation of the QNAP TS-230 storage drive.
- You should avoid potential damage or injury to the contents and also you have to ensure the NAS drive and take care of the internal system and its major components until they cool themself down.
- You should take help from an authorized, skilled, and qualified person who should have all the knowledge about the restrictions and the safety precautions to take and maintain the procedure with all physical access to the device.
- Also, you should have observed all the ESD (electrostatic discharge) to avoid any kind of injury to the internal system and its major components.
- Along with that, you need to ensure to store the device in a cool place and a secure location. You should have found a location where you can easily access, control, and monitor any means of security.
These are the safety instructions that you need to follow before you perform any operation with the storage NAS drive.
How to Install the QNAP TS-230 NAS Storage Drive?
Well, this section provides the ideal ideas to install and configure the storage NAS in the easiest ways. Before you install the storage drive, you have to maintain the hardware and the driver installation. Basically, the hardware installation consists of the information on installing drives, expansion cards, and memory modules. On the other side, the driver installation is compatible with 2.5-inch and 3.5-inch SATA hard drives, and also 2.5-inch solid-state drives.
Before Installation Instructions
Before you install the 3.5 inches drive trays or hard drives, there is a need to read the warning and cautions to prevent injuries and damage.
- From the moving fan blades, keep yourself away from the blades of a moving fan.
- Also, you need to observe the electrostatic discharge procedure to avoid any kind of damage to the internal system and the components of the device.
- Moreover, if you are installing a drive or installing a QTS then erase all the data from the drive before you begin the installation of the QNAP TS-230 NAS Storage Drive.
Installation Steps:
Now follow the installation of the storage drive without wasting another minute.
- First of all, you have to turn off the NAS storage for home drive.
- After that, you have to disconnect the power cord from the power wall outlet.
- Next, you have to disconnect all the external attachments and cables.
- Later, you need to remove the case cover. For that, you need to lay the storage drive on the left side and then unlatch the screw.
- Thereafter, you need to slide the back of the cover and slightly lift the cover of the storage drive.
- Next, you need to install a storage drive on a tray.
- Firstly, you need to remove a drive tray. Along with that, you have to pull the tray by pressing the latch at the same time.
- After that, safely remove the sides of the tray and fasten all the panels carefully.
- Afterward, you have to place the drive and tighten all the holes and the buttons on the drive so that they can align with each other.
- With the bottom holes on the drive tray, you have to fasten the panels and then lock the drive tray.
More
- Afterward, you have to load the tray into a bay and slightly push it into the drive bay and push the handle as well.
- Afterward, you have to attach the case cover by placing the cover on the storage drive and slightly forward by attaching all the screws to the bottom of the NAS.
- Now safely place the QNAP TS-230 storage device into its normal position and securely connect all the cables and the external attachments.
- Lastly, power on the NAS device.
This is it. These are the installation and the configuration steps of the QNAP TS-230 NAS drive. Follow the step-by-step to install it and use it at home.
QNAP TS-230 NAS Setup
Before the setup of the NAS storage drive, you have to read all the safety information and the requirements. This is necessary before you set up the device and install its components.
- Primarily, locate the NAS device in a safe place where it can easily meet all the network requirements.
- After that, you have to perform the installation of the device. The installation steps you can read into the above section.
- After completing the installation, you have to connect all the applicable cables and the power cords to the electrical outlet.
- After doing this, you have to turn on the NAS storage drive.
- Next step, you need to log into the drive using system IP address.
That is it. This is how the setup of the QNAP TS-230 NAS can be done.
How to perform the basic operations for the QNAP TS-230 NAS storage device?
To perform the basic operations of the NAS device, you should know first what is included in the basic operation. Generally, the basic operation includes power on, power off, force power off, basic system reset, and advanced reset operations. If you want to know how to perform these operations then read here.
- To perform the power-on operation, you have to press the button once and it will result that the NAS is powered on.
- To perform the power-off operation, you have to press or hold the power button for at least two seconds and the NAS will be powered off.
- To perform the basic system reset, you need to press or hold the power button for three seconds and it will result that all the existing settings would be erased such as admin password, TCP/IP configuration, system port, low-security level, erase the LCD panel password and the VLAN will be disabled.
- To perform the advanced system reset, you need to press the power button for at least 15 seconds. It will result that all the factory settings being restored. It also helps to retrieve the old data and you can also recreate the folder structure on your NAS.
This is how you can easily perform the basic operation. For more information about the QNAP TS-230 NAS storage device, you can refer to its user manual.
QNAP TS-230 NAS Review
In the review of the QNAP TS-230 NAS storage device, the users admire its functions and its features. However, it silently runs and comes in a very unique and traditional color which makes it perfect for smart homes. Moreover, you can slightly use it for office use as well. So far, it is ideal for a single stream for highly compressed videos. As it is ideal for a home and also provides a backup for the files and you can also enable a high level of protection to satisfy all your storage needs.