The ADT Alarm System is among the most effective systems available today. It protects you from fire, burglary, and smoke, in addition to monitoring your security throughout the day. As the owner of this alarm system, it is crucial to know how to operate your alarm system in a way that is effective. What happens if your ADT Door Chime alarm doesn’t sound when the door is opened?
Did your door chime suddenly stop working? This article will help you discover how to repair your door chime back to optimal working conditions. Let’s get started.
There may be several issues at the same time that cause the sensor for your door to stop working.
Know more- How do the setup of the Avantek wireless doorbell?
1. Worn-Out Batteries:
The batteries in the door sensor you are using are defective; it is necessary to replace them for the problem to be fixed.
2. The Sensor is Unprogrammed:
The sensor might be removed from the panel. In this case, you’ll need to pair it with your control panel.
3. Magnet not Attached Properly:
When the device can’t get in contact with its magnets, then it will not perform.
4. Software error with Sensor:
A problem with the sensor’s software can result in the device stopping functioning. The cause could be caused by a malfunctioning chime.
5. The Sensor is Damaged:
A sensor that is not working generally, results in an issue with the hardware, which is not likely, but it could be this is the problem you’re examining in your case.
First, you must know the reason why your doorbell from ADT was not functioning. Here are other few reasons your Door Chime from ADT isn’t functioning properly:
- The power of the battery is not sufficient.
- Power outage.
- Your ADT Door Chime is faulty.
For more information on how to fix these issues, continue reading.
ADT Door Chime Not Working: How to Troubleshoot
Recharge The ADT Door Chime Batteries
The battery of your ADT Door Chime could cease to function when the battery’s power is low. As you may have guessed, The Door Chime is battery-powered. Therefore, if the battery power is exhausted the device won’t work properly.
Similar Article- Experts’ Facts and Advantages of using the Arlo Wireless Doorbell
To find out if the battery in your ADT Door Chime is low, test your device’s touchscreen. The door chime’s touchpad can make a continuous beeping sound when the battery inside the device is depleted. Once you’ve confirmed the battery of your doorbell is at a low level, you can charge it to full.
The steps below will help you to charge your door Chime battery:
- The Battery pack of the ADT Door Chimes out of the device. To accomplish this, push and then hold down the tab on the base of the bracket. Slide it upwards, and remove the battery pack and away from your device.
- Plug the micro USB cable for the door chime into the port for charging the pack of batteries.
- Connect another end of your micro USB cable to a charger or charging station like the computer. If you’re using a charger for charging the ADT Door Chime battery You’ll also need to connect the charger to an outlet for power.
- Allow the battery to run for approximately 8 hours.
- If you’ve fully charged the battery, there will be a green light appear at the bottom of the battery. Remove the battery from the charger when you see the green light.
- Then, insert the battery pack back into the doorbell, then close it.
- Finally, place the ADT doorbell on the bracket that supports it and lower it until it clicks.
It is likely that your ADT Door Chime ought to be functioning immediately. However, if it doesn’t, go to the next problem-solving step.
Reset Your ADT Door Chime
The ADT Door Chime will require constant power to function. If you experience an outage of power in your home the door chime could disengage with the primary panel. To solve this issue, you’ll need to reset the door chime.
The steps below will allow you to reset your ADT Door Chime:
- Press your door chime’s touchpad to activate the display.
- Click in the Tools tab located in the bottom right of the screen that is home.
- Next, input your ADT master code.
- Tap Settings. Then select Chime.
- There is a switch beneath that Chime Tab. Turn the switch underneath the Chime tab to ON. This will bring back to turn off your ADT doorbell.
The ADT Door Chime will begin operating when the reset is complete.
Similar Post- Honeywell Wireless Doorbell Installation, Setup & Troubleshooting
Consult Your Technician
If your door chime from ADT isn’t working after you restarted the device, one or more components inside the device may be defective. Therefore, you may require replacing these parts in order to repair your door’s chime. But it is possible that you won’t be able to detect malfunctioning components of the door chime of ADT in the event that you’re not a tech. Ask an expert to examine your doorbell from ADT if you suspect that the device is defective. The specialist will pinpoint the parts that are damaged and will inform you of the problem. They can also advise you on how to find high-quality new parts to replace your door Chime.